One (1) Solar Taurus 70 Gas Engine skid consists of following:
-Solar outdoor enclosure, S/N TG00502, assembly 2-58881, Built 2000 dismantled
2019. ISO rating turbine continuous 7250 KWe (15 deg C/59 deg F, sea level, heat rate 10,650
kJ/kwe-hr/10,100 btu/kw-hr, thermal efficiency 32.8% , exhaust gas mass flow 98,900
kg/hr/215,840 lbs/hr at 490 deg C/910 deg f/ Turbine speed 15,200 rpm. Peak rating ISO 7628
kw. Site rating 6363 kw summer 90 Deg F, 25 PPM NOX and CO
Package hours and 2500 846 starts
-Engine Solar Taurus 70s, Version 9701S, S / N 00658. SoLoNOX, Natural gas
-Gear unit Solar Epicyclic, 13600 hp, ratio 8.21005, 15158/1800 rpm, Service factor 1.10,
Assembly no. 33085C-200, Serial no. SGK99-55329. With starting motor
-Sound attenuated enclosure , doors 85 DBA noise level. Axial side exhaust, top inlet air, inlet 4”
natural gas all associated accessories
One (1) Solar Generator skid consist of following:
-Kato synchronous AC generator, continuous rating 7200 kw, 9000 kw, voltage 12470 -13800 v
0.8 pf, 417 amps, 3 PHASE, 60 HZ, S/N 13937-01, Code 4P12-3600, Model No
A269660001
-Brushless exciter field amps 5, field volts 100, PMG 240 v, 180 hz
-Generator terminal box with 4 x 500:5 cts on phase side, neutral side 3x600:5 cts, 1 x 100:5 ct
-Solar Turbotronic control panel mounted side of enclosure

ADDITIONAL EQUIPMENT
One (1) set of bolts with nuts for Engine skid and generator skid
One (1) Gearbox to generator coupling with coupling guard, coupling bolts and nuts both sides
One (1) Air inlet system with ductwork, filter house, supporting structure.
One (1) Exhaust system with exhaust expansion joint, silencer, stack (total height of stack 38’6”)
One (1) Fire cylinder cabinet and control panel
One (1) Lube oil cooler
One (1) Engine skid enclosure air inlet duct
One (1) Engine skid enclosure air exhaust duct
One (1) Generator air inlet filter with duct
One (1) Generator air exhaust duct
One (1) Lube oil fume vent duct with fan
One (1) Power Ohm resister 200 amps, 10 secs neutral ground resister
One (1) Outdoor Electrical house consist of following:
-Generator breaker control panel with 1200 amps Siemens type 13-GMI-750-1200-58 circuit
breaker, 125 VDC trip and close, Beckwith M-3425 generator protection relay,
2 x 12,470:120 V pts on bus side, 2 x 12,470:120 V generator side, voltage regulator,
3 x 600:5 cts bus side
-Reliant 200 hp VFD for starting motor, 480 v

-Cutler Hammer MCC, 800 amps, 480 v
-Switchgear battery charger Constant Power Mfg co USGS-120-1PH-120-10, 120 vac in,
120 vdc, 10 amp dc out
-Turbine battery charger American battery charger model ABC11-120-20, 208-240 v ac in 120
Vdc 20 amps dc out.
-Batteries (advisable not to take it, because of age)
-Spare parts - filters, consumables etc.
One (1) Refurbished (purchased 2001) Universal Compression Arial JGR-2 natural gas compressor skid
100 psig inlet and 300 psig outlet
One (1) Station transformer padmount GE 750 kva, 12500 v to 480 v
One (1) set of walkways ladders
One (1) set of manuals and drawings
 

Murphy panel Serial Number, PM12081-AB

=====================

EQUIPMENT OVERVIEW

=====================

Condition
Overhaul Required

Manufactured
2003

Location
Slave Lake, Alberta

Registration:
Cooler and all vessels AB/BC/SK – except fuel gas scrubber is AB only.

Service:
Sour

Driver / Driven:
CAT 3512LE & Ariel JGE-4/3 with double distance pieces

Stages:
3

Cylinders & MAWP:
1st stage, 12.500”T x 2 @ 635psi;
2nd stage, 8.375” ET @ 800psi;
3rd stage, 5.500” ET@ 1725psi

Package MAWP:
1650 psi

Control Panel:
PLC

Cooler Manufacturer:
Hemphill

Additional Notes:
Preserved; Fire eyes (x2); Gas detection (x2); H2S detection (x2); Exhaust fan; 3 ton crane; Cata-Dyne heaters; Inlet pressure control valve; Auto/manual recycle; Auto/manual louvers; AC lighting; Ridge vent & overhead door in building and a 3 piece main skid.

1 MW of Power, 1 Fixed Price, 8 Weeks & GO!

1 MW Generator Turnkey Solution Summary

As an alternative to buying this generator as-is, we’ve prepared and can execute a full turnkey cost-saving power generation solution. Watch the video included and review the turnkey summary below.

Virtual 3D Tour

Objective: Supplying, delivering, fully installing, and commissioning a 1 MW Waukesha 7042GL natural gas powered complete prime power generation system.

Costing: Project will be executed with total cost certainty rolled into one up-front fixed price of $842,000 + taxes (capital lease and rent-to-own available). Everything is included in the one price (project scope available upon request); from the cost of the generator, site work and all the way through to commissioning.

Project Timeline: 8-10 Weeks from today

GENERAL PACKAGE CONFIGURATION

Waukesha L7024GL

• VHP, 12 cylinder
• Rated 1472 HP – 1097 kW @ 1200 RPM
• Rated Continuous Service
• Fuel – Natural Gas

Propak Fin Tube Aerial Cooler Assembly

• Jacket water section
• After-cooler section
• Belt Driven Fan from Engine

KATO 1000 kW Generator Assembly

• 6P6-1900 1000Kw/1250 KVA
• 277/480/3/60 VAC
• 1504 Amps
• Rated Continuous Service

Thompson MEC-20 Micro Controller Panel

• Synchronous Generator/Engine Controller
• Woodward Governor Control
• Main Breaker
• Engine Monitoring Annunciator

Kohler 60 kW Black Start Unit

• Engine – John Deere 4045TF150C
• Fuel – Diesel
• Generator – Kohler 60REQZI
• 62 kW
• 277/480/3/60 Vac
• 71 Amps

Eagle Instrument Air Compressor

• Qty. 2 screw compressors
• Qty. 2 TECO 20 HP, 480/3/60 VAC motors
• 100 Gallon Storage tank
• Automated air dryer assembly

Building & Skid

• Length 40’
• Width 20’
• Height 22’
• Weight 100,000 lbs.
• Qty. 4 Lifting lugs on each side of the skid/building assembly.

Additional Cooler Dimensions

• Width 20’
• Length 10’
• Height 12’

Inquiries

Contact us to learn more about this exciting 1MW turnkey and fixed-cost solution.

=====================

EQUIPMENT OVERVIEW

=====================

Designed to work with 150HP Jet pump packages (sold separately), these separators are designed two phase, but the designers really had a fascination with level gauges, and as such you will have amazing optics on what is happening inside the vessel.  There are 5 available, 2 are new – 3 are used and in great condition still.  All of them are located in an easy access yard in Grande Prairie, Alberta for easy removal and transport to your site.

==================

360º VIRTUAL TOUR

==================

Explore this package in rich detail through a virtual walkthrough here:

https://my.matterport.com/show/?m=czduR3FeGUP

==========

DRAWINGS

==========

Drawings available upon request.

=========================

ADDITIONAL INFORMATION

=========================

Condition:

5 Currently Available –  2 NEW / 3 USED (less than 2 years)

Manufactured:

2012 by ES Fox

Location:

Grande Prairie, AB

Status:

Disconnected; in Yard

Registration:

U Stamp; AB/BC/SK CRN

Service:

Sour

Phases:

2 Phase

Electrical:

Used ones are wired to JB’s; New ones have no electrical installed

Shipping Dimension:

29’ 7” L x 12’ 4” W x 10’ 2” H

Package Comments:

Originally designed to work together with Weatherford W165 triplex jet pump packages

Immediately available 3 Coil tube trucks.

All extra parts, tooling, maintanance supplies and BOP will be included in price of purchase.

2002 Western Star Tri drive,  435 Caterpillar engine c/w 18 speed transmision

- 330 CFM compressor

- DA injector

- Holds 3000M of 1 1/4

- Coil type 3/4 - 1 1/4

-  C/W Knuckle picker

This unit will need some maintanance before being placed back into service.

2004 Peterbilt conventional Tandom tandom, Caterpillar C15 engine, 18 speed transmision.

- 660 CFM Hurricane compressor

- National injector T25

- Holds 3000 M of 1 1/2

- coil type 1 1/4-1 3/4

- C/W Knuckle picker.

Ready for service.

2007 Peterbilt conventional Tri drive, Caterpillar C15, 18 speed transmision.

- 660 CFM Hurricane compressor

- DA injectors

- holds 3000 M of 1 1/2

- Coil type 3/4 - 1 3/4

- C/W Knuckle picker.

Ready for service.